Industrial Computer Based on Raspberry Pi CM4
- Broadcom BCM2711, quad core Arm Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
- Up to 8GB LPDDR4 RAM and 32GB eMMC storage
- Support micro-SD Card and mSATA SSD storage expansion
- 3 x Gigabit Ethernet ports, 1 x USB 3.0 port
- 2.4GHz and 5GHz dual-band Wi-Fi, Bluetooth and 4G
- Wide voltage power input range of DC 9V~36V with reverse polarity protection, overvoltage protection and overcurrent protection
- Integrated supercapacitor (backup power supply, optional) , RTC, Watch Dog, EEPROM and crypto authentication
- Wide temperature range of -25℃~60℃ for working environment
- High-quality metal case, compatible with DIN-rail installation
| |
System |
---|
CPU | Broadcom BCM2711, quad core Arm Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz |
VPU | H.265(HEVC), up to 4Kp60 decode H.264, up to 1080p60 decode, 1080p30 encode |
GPU | OpenGL ES 3.1 & Vulkan 1.0 |
Memory | Options for 1GB, 2GB, 4GB, 8GB LPDDR4-3200 SDRAM |
Storage | Options for 0GB, 8GB, 16GB, 32GB eMMC storage Micro SD card, supporting to select the 00GB/32GB/64GB SD card mSATA SSD (optional) |
software |
---|
Operating System | Raspberry Pi OS (Desktop) 32-bit Raspberry Pi OS (Lite) 32-bit Raspberry Pi OS (Desktop) 64-bit Raspberry Pi OS (Lite) 64-bit |
Front I/O |
---|
Power | 1 x DC IN, 2-Pin 3.5mm pitch phoenix terminals with screw holes. It supports 9V~36V input, the signal is defined as VIN+/GND. |
Audio (optional) | 1 x Audio In/Stereo Out, 3.5mm audio jack connector. It can be used as MIC IN and LNE OUT. - When a headphone is connected, the audio output switches to the headphone.
- When no headphone is connected, the audio output switches to the speaker.
Note: Only ED-IPC2220 contains this interface. |
1000M Ethernet(ETH0) | 1 x adaptive 10/100/1000M ethernet port, RJ45 connector. It can be used to access the network. PoE can be supported through expansion module. |
1000M Ethernet(ETH1Ð2) | 2 x adaptive 10/100/1000M ethernet ports, RJ45 connector. It can be used to access the network. |
USB3.0 | 1 x USB 3.0 port, type A connector, which supports up to 5Gbps transmission rate. |
Rear I/O |
---|
SD Card Slot | 1 x Micro SD card slot, which is used to install SD card. It supports booting the OS from SD card. |
SIM Card Slot | 1 x Nano SIM card slot, which is used to install SIM card for getting 4G signal. |
Micro USB | 1 x Micro USB port, which supports to flash to eMMC for the system. |
Side I/O |
---|
HDMI | 1 x HDMI port, type A connector. It is compatible with HDMI 2.0 standard and supports 4K 60Hz. |
USB 2.0 | 2 x USB 2.0 ports, type A connector, which support up to 480Mbps transmission rate. |
Antenna | 2 x SMA ports, which is used to connect 4G antenna and Wi-Fi/BT antenna. |
Buttons and Indicators |
---|
Reset | 1 x Reset button, which can reset the device. |
PWR | 1 x red power indicator, which is used to check the status of device power-on and power-off. |
4G | 1 x green 4G indicator, which is used to check the status of 4G signal. |
ACT | 1 x green system indicator, which is used to check the working status of device. |
USER | 1 x green user indicator, user can customize a status according to actual application. |
Expansion I/O |
---|
12V 1A | 3 x DC OUT, 2-Pin 2.0mm pitch WTB connector, supporting 12V 1A output. These pins are defined as GND/12V, reserving to provide power supply for extended LCD. |
5V 1A | 1 x DC OUT, 3-Pin 2.0mm pitch WTB connector, supporting 12V 1A output. These pins are defined as GND/5V/GND, reserving to provide power supply for extended LCD. |
40-Pin GPIO | 1 x GPIO, 2x20-Pin 2.54mm pitch header, using to lead out the GPIO ports of CM4. - These pins are defined as GPIO1~GPIO27/3V3/5V2/GND
- It is Compatible with expansion modules, reserving to connect expansion accessories.
|
10-Pin GPIO | 1 x GPIO Pin Header, 2x5-pin 2.54mm pitch header, using to lead out the expansion GPIO ports. User can customize the function according to actual application, these pins are defined as 8xGPIO/3V3/GND. |
CSI (optional) | 1 x Pin Header, 2x15-pin 0.4mm pitch connector, supporting 2-Lane CSI signal. It can be used to connect 8-megapixel CSI camera. Note: Only ED-IPC2220 contains this interface. |
HDMI (optional) | 1 x FPC HDMI, 40-pin 0.5mm pitch FPC connector, which can be reserved to connect extended LCD, supporting USB/I2C touch screen and backlight adjustment.
Note: Only ED-IPC2220 contains this interface. |
DSI (optional) | 1 x FPC DSI, 30-pin 0.5mm pitch FPC connector, supporting 4-Lane DSI signal. It can be reserved to connect extended LCD, supporting USB/I2C touch screen and backlight adjustment. Note: Only ED-IPC2220 contains this interface. |
USB2.0 | 2 x USB 2.0, 5-pin 1.5mm pitch WTB connector, which can be expanded USB 2.0 ports. |
mSATA | 2 x USB 2.0, 5-pin 1.5mm pitch WTB connector, which can be expanded USB 2.0 ports. |
Speaker (optional) | 1 x PA output, 4-pin 1.5mm pitch WTB connector, dual channel stereo audio output. It can be extended to connect two 4Ω 3W stereo speakers, these pins are defined as R+/R-/L+/L-. Note: Only ED-IPC2220 contains this interface. |
Expansion Performance |
---|
EEPROM | Supports 4K byte storage and improves the ease of use of device. |
Crypto Authentication | It can be matched to realize the required upper layer application and improves the security of device. |
RTC | RTC with 1F SuperCAP backup, which can ensure that the system clock is not affected by device power-off. We also provide a battery base, and you can buy a CR1220 battery backup for RTC. |
Buzzer | A tip or an abnormity can be configurated according to actual application, which realizes the alarm function. |
Watch Dog* | This function has been reserved on hardware. But we need additional software to support it, which is under development. |
Electrical Characteristics |
---|
Input Voltage | 9V ~ 36V DC |
Power Consumption | 24W (Max) |
Mechanical Characteristics |
---|
Dimensions | 143mm x 100mm x 34mm (WxDxH, DIN-rail and antenna are not included) |
Weight | 750g |
Installation | DIN-rail mounting |
Wireless |
---|
Wi-Fi/Bluetooth (optional) | 2.4GHz & 5GHz dual-band Wi-Fi and Bluetooth with antenna. - 2.4GHz Wi-Fi: Compatible with IEEE 802.11 b/g/n
- 5GHz Wi-Fi: Compatible with IEEE 802.11 a/n/ac
- The Bluetooth supports 2402MHz ~ 2480MHz frequency
|
4G (optional) | Connect with various 4G LTE modules through the Mini PCIe interface, with antenna. - EC20-CE Module (China/India)
- LTE FDD: B1/B3
- LTE TDD: B38/B39/B40/B41
- TDSCDMA: B34/B39
- WCDMA: B1
- CDMA 1x/EVDO: BC0
- GSM: 900/1800MH
- EC25-AFX Module (North America)
- LTE-FDD:B2/B4/B5/B12/B13/B14/B66/B71
- LTE-TDD
- WCDMA: B2/B4/B5
- GSM/EDGE
- EC25-AUX Module (Latin America/Australia/New Zealand)
- LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B28
- LTE-TDD: B40
- WCDMA: B1/B2/B4/B5/B8
- GSM/EDGE: B2/B3/B5/B8
- EC25-EUX Module (Europe/Middle East/Africa/Thailand)
- LTE-FDD: B1/B3/B7/B8/B20/B28A
- LTE-TDD: B38/B40/B41
- WCDMA: B1/B8
- GSM/EDGE: B3/B8
|
Environmental & Regulatory |
---|
Operating Temperature | -25°C ~ 60°C |
Storage Temperature | -25°C ~ 60°C |
Ambient humidity | 5% ~ 95% (non-condensing) |
Certifications | - FCC
FCC 47 CFR Part 15 Subpart B - CE
- EN IEC 62368-1/EN IEC 62311/EN IEC 61000-3-2/EN IEC 61000-3-3
- EN 55032/EN 55035
- EN 301 489-1/EN 301 489-3/EN 301 489-17/EN 301 489-52
- EN 301 328/EN 301 440/EN 301 511/EN 301 908-1/EN 301 908-2
|
Unit: mm
You can choose a power adapter according to actual needs.
Model | Description | Picture |
---|
ED-PSU1202-UK-3.5PL | 100~240VAC to12VDC/2A Adapter, with UK AC plug, 3.5mm pitch phoenix plug with lock | |
ED-PSU1202-US-3.5PL | 100~240VAC to 12VDC/2A Adapter, with US AC plug, 3.5mm pitch phoenix plug with lock |
ED-PSU1202-AU-3.5PL | 100~240VAC to 12VDC/2A Adapter, with AU AC plug, 3.5mm pitch phoenix plug with lock |
ED-PSU1202-EU-3.5PL | 100~240VAC to 12VDC/2A Adapter, with EU AC plug, 3.5mm pitch phoenix plug with lock |
NOTE: Each model contains only one of the UK, US, AU and EU plugs. |
- 1 x ED-IPC2200 Unit
- [Wi-Fi/BT Version - optional] 1 x 2.4GHz/5GHz Wi-Fi/BT Antenna
- [4G Version - optional] 1 x 4G/LTE Antenna